石油学报 ›› 2003, Vol. 24 ›› Issue (4): 108-112.DOI: 10.7623/syxb200304025

• 石油工程 • 上一篇    

水驱抽油机井杆管偏磨原因的力学分析

董世民   

  1. 燕山大学机械工程学院, 河北秦皇岛, 066004
  • 收稿日期:2002-05-10 修回日期:2002-09-26 出版日期:2003-07-25 发布日期:2010-05-21
  • 作者简介:董世民,男,1962年9月生,1998年获西南石油学院博士学位,现为燕山大学机械工程学院教授.
  • 基金资助:
    中国石油天然气集团公司"九五"科技攻关项目(97科字116号)部分成果.

Mechanical analysis on causes of worn rod string and tubing of rod pumping wells in the water-flooding oilfield

Dong Shi-min   

  1. Mechanical Engineering College of Yanshan University, Qinhuangdao 066004, China
  • Received:2002-05-10 Revised:2002-09-26 Online:2003-07-25 Published:2010-05-21

摘要: 建立了铅垂油井杆管偏磨临界轴向压力的计算公式.杆管偏磨的临界轴向压力只取决于抽油杆直径与轴向分布力;应用波动方程建立了抽油杆柱轴向分布力的模拟方法;建立了供液不足油井液击力的计算公式,改进了柱塞下行阻力的计算方法.系统分析了油井生产条件与生产参数对杆管偏磨的临界轴向压力与柱塞下行阻力的影响.分析结果表明:(1)含水与沉没度对杆管偏磨有显著影响,高含水油井在低沉没度下运行会明显降低杆管偏磨的临界轴向压力;(2)当油井供液不足时,柱塞下冲程时泵内将产生液击,并加大柱塞下行阻力;(3)抽汲参数增加不仅导致抽油杆柱振动加剧,降低了杆管偏磨的临界轴向压力,而且也加大了柱塞下行阻力.当抽油杆柱在上述一个或几个条件共同作用下达到偏磨临界条件时,杆管将产生偏磨.

关键词: 抽油机井, 水驱, 杆管偏磨, 临界条件, 力学机理

Abstract: The calculating formula for critical axial load of worn rod string and tubing was set up.The critical axial load only depends on the diameter and axial distributed load of the rod string.The simulating method of axial distributed load of the rod string was given by means of the wave equation of the rod string.The formula for calculating the liquid shock load in the low sinking depth wells was set up,and the formula for the axial load in the down stroke of the plunger was established.The influences of running conditions of the oil wells on the wear of rod string and tubing were systematically analyzed.The bellow conclusions can be obtained:(1) The water content ratio and the low sinking depth have important affect on the wear of rod string and tubing.When the wells run at the low sinking depth,the critical axial load is greatly reduced.(2) When the pump cylinder could not be filled with enough liquid,the liquid shock will occur,and the liquid shock load will make the down stroke axial load of the plunger increase.(3) When the suction parameters of the wells increase,the critical axial load will decrease,and the down stroke axial load of the plunger will increase.When wells run at one or some of the above states,and the practical down stroke axial load of the plunger is greater than the critical axial load,the wear of rod string and tubing will take place.

Key words: rod pumping system, water-flooding oilfield, rod string and tubing, wear, critical condition, mechanics

中图分类号: