稠油环空掺稀气举技术——以吐哈油田吐玉克区块为例

doi:10.7623/syxb201502011

石油学报 ›› 2015, Vol. 36 ›› Issue (2): 217-223.DOI: 10.7623/syxb201502011

稠油环空掺稀气举技术——以吐哈油田吐玉克区块为例

刘忠能^1,2, 钟海全¹, 李颖川¹, 刘彦哲², 毛建文², 王鹏²

1. 西南石油大学油气藏地质及开发工程国家重点实验室四川成都 610500;
2. 中国石油长庆油田公司第九采油厂宁夏银川 750000

收稿日期:2014-07-31 修回日期:2014-11-07 出版日期:2015-02-25 发布日期:2015-02-05
通讯作者: 刘忠能,男,1988年2月生,2010年获西南石油大学石油工程专业学士学位,2013年获西南石油大学油气田开发工程专业硕士学位,现为中国石油长庆油田公司第九采油厂油藏工程师,主要从事采油采气工艺及油藏开发理论的研究。Email:lzngxs@163.com
作者简介:刘忠能,男,1988年2月生,2010年获西南石油大学石油工程专业学士学位,2013年获西南石油大学油气田开发工程专业硕士学位,现为中国石油长庆油田公司第九采油厂油藏工程师,主要从事采油采气工艺及油藏开发理论的研究。Email:lzngxs@163.com
基金资助:
国家重大科技专项(2008ZX05049-004)资助。

Heavy oil gas-lift technology assisted with light oil:a case study from Tuyuk block in Tuha oilfield

Liu Zhongneng^1,2, Zhong Haiquan¹, Li Yingchuan¹, Liu Yanzhe², Mao Jianwen², Wang Peng²

1. State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation, Southwest Petroleum University, Sichuan Chengdu 610500, China;
2. No.9 Oil Production Plant, PetroChina Changqing Oilfield Company, Ningxia Yinchuan 750000, China

Received:2014-07-31 Revised:2014-11-07 Online:2015-02-25 Published:2015-02-05

摘要/Abstract

摘要：

为了提高稠油冷采开发水平,利用高18.25 m的垂直多相管流实验回路开展了稠油气举流动实验及压降模型优选。基于实验结果及井筒传热机理,建立了环空掺稀气举井筒压力-温度梯度耦合预测模型,并可通过耦合环空与油管内流动进行循环迭代求解。实验结果表明:注气有助于稠油与稀油更快更充分混合;压降模型优选表明,Ansari模型误差相对最小,为12.12% 。针对吐哈油田吐玉克区块稠油井筒举升困难的实际情况,提出了稠油环空掺稀+气举工艺思路,并开展了实例井掺稀气举设计,对注气量、掺稀量等进行了敏感性分析。实例设计结果表明,实例井仅靠气举无法生产,其掺稀生产极限产量可达到16 m³/d,而掺稀+气举极限产量能达到52.5 m³/d;定产油量条件下,在特定范围内增加注气量能极大地减小掺稀量,且井底掺稀气举能极大地提升稠油井的产能。

关键词: 稠油, 实验, 压力-温度耦合, 掺稀气举, 工艺设计

Abstract:

To improve the cold production of heavy oil, heavy oil gas-lift flowing experiments and optimization of pressure drop model were carried out using 18.25 m vertical multiphase pipe flow test loop. Based on the experiment results and wellbore heat transfer mechanism, wellbore pressure-temperature gradient coupling predictive model was established for gas lift and annulus blending diluting technologies. Moreover, it can be solved by coupling the annulus and tubing flow with the use of loop iteration method. The experiment results show that gas injection can facilitate the sufficient blending of light and heavy oil. The model optimization indicates that Ansari model has the least error of 12.12%. It is difficult to lift the heavy oil wellbore in Tuyuke block of Tuha oilfield, aiming at which gas lift and blending diluting oil technologies was proposed with example design. Then a sensitivity analysis was carried out on the volume of injected gas and added light oil, etc. The example design demonstrates that the well cannot produce only based on gas-lift technology; the maximum productivity is 16 m³/d if applying diluting technology, while in combination with gas-lift technology the maximum output can reach 52.5 m³/d. In case of fixed oil production, the increasing volume of injected gas within the specific range can largely reduce the amount of added light oil, and the productivity of heavy oil well can be significantly improved using gas-lift and blending diluting oil technologies.

Key words: heavy oil, experiment, pressure-temperature coupling, gas-lift assisted with light oil, technological design

中图分类号:

TE355.3

刘忠能, 钟海全, 李颖川, 刘彦哲, 毛建文, 王鹏. 稠油环空掺稀气举技术——以吐哈油田吐玉克区块为例[J]. 石油学报, 2015, 36(2): 217-223.

Liu Zhongneng, Zhong Haiquan, Li Yingchuan, Liu Yanzhe, Mao Jianwen, Wang Peng. Heavy oil gas-lift technology assisted with light oil:a case study from Tuyuk block in Tuha oilfield[J]. Acta Petrolei Sinica, 2015, 36(2): 217-223.

参考文献

[1] 于连东.世界稠油资源的分布及其开采技术的现状与展望[J].特种油气藏,2001,8(2):98-103.
Yu Liandong.Distribution of world heavy oil reserves and its recovery technologies and future[J].Special Oil and Gas Reservoirs,2001,8(2):98-103.
[2] 李雁鸿,吴永彬,赵法军,等.溶剂蒸气萃取脱沥青的影响因素实验[J].石油学报,2014,35(5):935-940.
Li Yanhong,Wu Yongbin,Zhao Fajun,et al.Influence factors experiment of deasphalting in solvent vapor extraction[J].Acta Petrolei Sinica,2014,35(5):935-940.
[3] 鹿腾,李兆敏,李松岩,等.稠油溶解气驱渗流特征物理模拟和数值模拟[J].石油学报,2014,35(2):332-339.
Lu Teng,Li Zhaomin,Li Songyan,et al.Physical and numerical simulations of flow characteristics in solution gas drive for heavy oils[J].Acta Petrolei Sinica,2014,35(2):332-339.
[4] Akhiyarov D T,Zhang Hongquan,Sarica C.High-viscosity oil-gas flow in vertical pipe[R].OTC 20617,2010.
[5] Wang Shufan,Zhang Hongquan,Sarica C,et al.Experimental study of high-viscosity oil/water/gas three-phase flow in horizontal and upward vertical pipes[R].SPE 163148,2013.
[6] Blann J R,Garcia R,Guaramata F,et al.Advances in heavy oil lifting in the morichal area of venezuela[R].SPE 52211,1999.
[7] Butler R M,Bharatha S,Yee C T.Natural and gas-lift in SAGD production wells[R].PETSOC 97111,1997.
[8] Dewan J T,Elfarr J.Lifting of heavy oil with inert-gas-operated chamber pumps[R].SPE 9913,1981.
[9] Trindade W L,Branco C C M.The offshore heavy oil development challenges in Brazil[R].SPE 97381,2005.
[10] Targac G W,Redman R S,Davis E R,et al.Unlocking the value in west sak heavy oil[R].SPE 97856,2005.
[11] Gokcal B,Al-Sarkhi A S,Sarica C.Effects of high oil viscosity on drift velocity for horizontal and upward inclined pipes[J].SPE 115342,2009.
[12] Ortiz-Volcan J L.Development of heavy oil offshore lake maracaibo field using slug gas lift:a case history[R].SPE 143920,2011.
[13] Amani M.Gas well de-watering system and hydraulic gas pump,new designs and a discussion on their economics[R].SPE 29163,1994.
[14] Blann J R,Garicia R,Guaramata F,et al.Advances in heavy oil lifting in the morichal area of venezuela[R].SPE 52211,1999.
[15] Brito F J,Garcia L,Brown J C.Use of natural gas as a driving force in a diluent-gas artificial-lift system applied to heavy oils[R].SPE 139105,2010.
[16] Hernandez A,Marcelo R.Field scale research on gas chamber pumps[R].SPE 77729,2002.
[17] Dou Hongen,Chang Yuwen,Hu Dandan,et al.Application of gas lift to heavy-oil reservoir in intercampo oilfield,venezuela[R].SPE 97370,2005.
[18] Dou Hongen,Chang Yuwen,Hu Dandan,et al.Application of gas lift technology to a high-water-cut heavy-oil reservoir in intercampo oilfield,venezuela[R].SPE 97370,2007.
[19] 林日亿,李兆敏,王景瑞,等.塔河油田超深井井筒掺稀降粘技术研究[J].石油学报,2006,27(3):115-119.
Lin Riyi,Li Zhaomin,Wang Jingrui,et al.Technology of blending diluting oil in ultra-deep wellbore of Tahe Oil field[J].Acta Petrolei Sinica,2006,27(3):115-119.
[20] 石在虹,石爽,韩冬深,等.稠油掺稀多相流动规律及生产参数设计[J].水动力研究与进展:A辑,2012,27(3):284-291.
Shi Zaihong,Shi Shuang,Han Dongshen,et al.Multi-phase flowing law and production parameter design of heavy oil mixing with light oil[J].Chinese Journal of Hydrodynamics:Series A,2012,27(3):284-291.
[21] Ansari A M,Sylvester N D,Sarica C,et al.A comprehensive mechanistic model for upward two-phase flow in wellbores[R].SPE 20630,1994.
[22] 梁金国,徐明海.稠油井闭式热流体循环井筒温场计算与抽油杆柱设计[J].石油大学学报:自然科学版,1993,17(3):46-50.
Liang Jinguo,Xu Minghai.Wellbore hot fluid circulation and sucked-rod design for heavy oil wells[J].Journal of the University of Petroleum,China,1993,17(3):46-50.
[23] 任瑛.加热开采稠油工艺的探讨-井筒中的热流体循环[J].华东石油学院学报,1982,17(4):53-66.
Ren Ying.Thermal production of viscous oil with recycling of hot fluid in well bore[J].Journal of East Petroleum College,1982,17(4):53-66.
[24] 吴晓东,师俊峰,竺彪.循环热流体开采稠油优化设计方法研究[J].石油钻探技术,2006,34(6):1-3.
Wu Xiaodong,Shi Junfeng,Zhu Biao.A study of recovering heavy-oil reservoir with hot fluids[J].Petroleum Drilling Techniques,2006,34(6):1-3.
[25] Shu W R.A viscosity correlation for mixtures of heavy oil,bitumen,and petroleum fractions[J].SPE 11280,1984.
[26] 刘德生,宫敬,吴海浩,等.三相流动条件下的油水混合物粘度[J].油气储运,2010,30(2):107-110.
Liu Desheng,Gong Jing,Wu Haihao,et al.Viscosity of oil-water mixtures in three-phase flow[J].Oil & Gas Storage and Transportation,2010,30(2):107-110.
[27] Mukherjee H,Brill J P.Pressure drop correlations for inclined two-phase flow[J].Journal of Energy Resources Technology,1985,107(4):549-554.
[28] 李颖川.采油工程[M].第二版.北京:石油工业出版社,2009:33-35.
Li Yingchuan.Production engineering [M].2nd ed.Beijing:Petroleum Industry Press,2009:33-35.

稠油环空掺稀气举技术——以吐哈油田吐玉克区块为例

Heavy oil gas-lift technology assisted with light oil:a case study from Tuyuk block in Tuha oilfield

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	王正茂, 韩旭, 潘峰, 樊宇, 阎逸群, 周小松, 李诚. 驱油用乳液聚合物性能评价与现场试验[J]. 石油学报, 2024, 45(6): 976-987.
[2]	李博良, 李宾飞, 冀延民, 盖平原, 王建, 李兆敏, 王成建. 烟道气辅助注蒸汽开采稠油增效机理及应用[J]. 石油学报, 2024, 45(3): 574-585.
[3]	鹿腾, 李兆敏, 顾子涵, 穆金峰, 丁国, 王一平, 杜华君. 超深层稠油降黏泡沫体系微观作用机理及其矿场应用[J]. 石油学报, 2023, 44(8): 1344-1355.
[4]	陈刚强, 张磊, 王东勇, 马万云, 牛志杰, 邹贤利. 准噶尔盆地乌尔禾地区稀油—稠油—油砂—沥青立体成藏(成矿)模式[J]. 石油学报, 2023, 44(7): 1072-1084.
[5]	关文龙, 蒋有伟, 郭二鹏, 王伯军. “双碳”目标背景下的稠油开发对策[J]. 石油学报, 2023, 44(5): 826-840.
[6]	孙焕泉, 刘慧卿, 王海涛, 束青林, 吴光焕, 杨元亮. 中国稠油热采开发技术与发展方向[J]. 石油学报, 2022, 43(11): 1664-1674.
[7]	鹿腾, 班晓春, 李兆敏, 高永荣, 郭二鹏, 杨建平, 马宏斌, 王宏远, 魏耀. 烟道气辅助SAGD蒸汽腔扩展机理[J]. 石油学报, 2021, 42(8): 1072-1080.
[8]	闫霄鹏, 许成元, 康毅力, 商翔宇, 经浩然, 林冲, 张敬逸. 基于力链网络表征的裂缝封堵层结构失稳细观力学机制[J]. 石油学报, 2021, 42(6): 765-775.
[9]	李晓光. 辽河坳陷欢喜岭油田稠油成藏条件及勘探开发关键技术[J]. 石油学报, 2021, 42(4): 541-560.
[10]	张胜飞, 孙新革, 苟燕, 张忠义, 王红庄, 周晓义, 解阳波, 吕柏林. 流量控制器在SAGD技术中的应用现状及思考[J]. 石油学报, 2021, 42(10): 1395-1404.
[11]	曹英权, 王清斌, 曲希玉, 王冠民, 苗长盛, 高媛, 陈思芮. 岩屑的有机酸溶蚀实验及验证——以渤中凹陷CFD6-4油田东营组为例[J]. 石油学报, 2020, 41(7): 841-852.
[12]	黄中伟, 张世昆, 李根生, 杨睿月, 武晓光, 张宏源, Kamy Sepehrnoori. 液氮磨料射流破碎高温花岗岩机理[J]. 石油学报, 2020, 41(5): 604-614.
[13]	张辉, 蔡志翔, 陈安明, 刘科柔, 杨茂林, 余庆, 王昊, 谭天一, 陈雨飞. 液相放电等离子体破岩室内实验与破岩机理[J]. 石油学报, 2020, 41(5): 615-628.
[14]	窦晓峰, 宁伏龙, 李彦龙, 刘昌岭, 孙嘉鑫, 李杨, 李晓东, 赵颖杰, 张凌, 刘乐乐. 基于连续-离散介质耦合的水合物储层出砂数值模拟[J]. 石油学报, 2020, 41(5): 629-642.
[15]	孙宝江, 彭玉丹, 张伟国, 赵艳玲, 陈济颖, 付光明. 筛管压溃强度计算公式及适用性[J]. 石油学报, 2020, 41(3): 363-371.