非均质底水油藏水平井ICD完井优化设计

doi:10.7623/syxb201710011

石油学报 ›› 2017, Vol. 38 ›› Issue (10): 1200-1209.DOI: 10.7623/syxb201710011

非均质底水油藏水平井ICD完井优化设计

罗伟^1,2, 林永茂², 李海涛¹, 蒋祖军², 伍强², 陶正武³

1. 西南石油大学油气藏地质及开发工程国家重点实验室四川成都 610500;
2. 中国石油化工股份有限公司西南油气分公司石油工程技术研究院四川德阳 618000;
3. 中国石油塔里木油田公司勘探开发研究院新疆库尔勒 841000

收稿日期:2017-01-08 修回日期:2017-06-29 出版日期:2017-10-25 发布日期:2017-11-02
通讯作者: 罗伟,男,1986年7月生,2010年获西南石油大学学士学位,2015年获西南石油大学博士学位,现为中国石油化工股份有限公司西南油气分公司博士后,主要从事水平井半智能与智能控水完井方面的研究工作.Email:lwswpu@163.com
作者简介:罗伟,男,1986年7月生,2010年获西南石油大学学士学位,2015年获西南石油大学博士学位,现为中国石油化工股份有限公司西南油气分公司博士后,主要从事水平井半智能与智能控水完井方面的研究工作.Email:lwswpu@163.com
基金资助:
国家重大科技专项"四川盆地致密碎屑岩完井与储层改造技术研究"（2016ZX05002-004-006）资助。

ICD completion optimization design of horizontal wells in heterogeneous bottom-water reservoirs

Luo Wei^1,2, Lin Yongmao², Li Haitao¹, Jiang Zujun², Wu Qiang², Tao Zhengwu³

1. State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation, Southwest Petroleum University, Sichuan Chengdu 610500, China;
2. Research Institute for Engineering Technology, Sinopec Southwest Oil & Gas Company, Sichuan Deyang 618000, China;
3. Research Institute of Exploration and Development, PetroChina Tarim Oilfield Company, Xinjiang Korla 841000, China

Received:2017-01-08 Revised:2017-06-29 Online:2017-10-25 Published:2017-11-02

摘要/Abstract

摘要：

流入控制阀（ICD）完井动态模拟预测和完井参数优化设计是ICD完井实现水平井生产优化的生命基础。结合半解析耦合模型和Eclipse 2011，建立稳态模拟和瞬态模拟相结合的ICD完井动态模拟方法。该方法不仅是以某一时刻的完井动态为设计依据，而是同时从整个生产周期内井筒与油藏流动动态最佳的角度来优化设计完井参数。针对非均质底水油藏，利用建立的模拟方法进行了ICD完井实例计算与参数敏感性分析，并分别提出了不同布置方式下的ICD完井优化设计方法。结果表明：ICD完井相对于常规完井能显著改善水平井的生产动态；ICD限流强度的确定需综合考虑产液剖面均匀程度和水平井采油指数，ICD完井存在一个最优ICD限流强度；对于非均质底水油藏，水平井ICD完井存在一个最优封隔器个数，其与具体储层的渗透率非均质程度密切相关；变化布置ICD完井设计相对于统一布置ICD完井设计不仅能使产液剖面更均匀，而且还能提高水平井的采油指数。

关键词: 非均质底水油藏, ICD完井, 动态模拟, 完井参数优化, 水平井

Abstract:

The performance simulation and prediction of inflow control devices (ICD)completion and the optimization design of completion parameters are the survival foundation of ICD completion to achieve the production optimization of horizontal wells. According to semi-analytical coupling model and Eclipse 2011, a dynamic simulation method of ICD completion was established by integrating steady-state simulation and transient-state simulation. This method not only takes the completion dynamics at a specific time as design basis, but also optimizes and designs completion parameters from the view of optimal wellbore and reservoir flow dynamics throughout the whole production cycle. Aiming at the heterogeneous bottom-water reservoir, the above simulation method was used for example calculation and parameter sensitivity analysis of ICD completion. In addition, the optimization design methods of ICD completion were put forward for different arrangement patterns. The result shows that ICD completion can considerably improve the production dynamics of horizontal wells compared with conventional completion. The determination of ICD flow-restriction sizes needs to consider the production profile uniformity and horizontal well productivity index comprehensively, and ICD completion is featured with the optimal flow-restriction sizes. For a heterogeneous bottom-water reservoir, ICD completion of horizontal well is featured with the optimal packer number, which is highly related with the degree of permeability heterogeneity for a specific reservoir. Variable ICD completion design not only further improves the production profile uniformity, but also increases the horizontal well productivity index compared with uniform ICD completion design.

Key words: heterogeneous bottom-water reservoir, ICD completion, dynamic simulation, completion parameter optimization, horizontal well

中图分类号:

TE257

罗伟, 林永茂, 李海涛, 蒋祖军, 伍强, 陶正武. 非均质底水油藏水平井ICD完井优化设计[J]. 石油学报, 2017, 38(10): 1200-1209.

Luo Wei, Lin Yongmao, Li Haitao, Jiang Zujun, Wu Qiang, Tao Zhengwu. ICD completion optimization design of horizontal wells in heterogeneous bottom-water reservoirs[J]. Acta Petrolei Sinica, 2017, 38(10): 1200-1209.

参考文献

[1] SAGGAF M M.A vision for future upstream technologies[J].Journal of Petroleum Technology,2008,60(3):54-98.
[2] 崔传智,徐建鹏,王端平,等.特高含水阶段新型水驱特征曲线[J].石油学报,2015,36(10):1267-1271.
CUI Chuanzhi,XU Jianpeng,WANG Duanping,et al.A new water flooding characteristic curve at ultra-high water cut stage[J].Acta Petrolei Sinica,2015,36(10):1267-1271.
[3] 杜庆龙.长期注水开发砂岩油田储层渗透率变化规律及微观机理[J].石油学报,2016,37(9):1159-1164.
DU Qinglong.Variation law and microscopic mechanism of permeability in sandstone reservoir during long-term water flooding development[J].Acta Petrolei Sinica,2016,37(9):1159-1164.
[4] 朱丽红,杜庆龙,姜雪岩,等.陆相多层砂岩油藏特高含水期三大矛盾特征及对策[J].石油学报,2015,36(2):210-216.
ZHU Lihong,DU Qinglong,JIANG Xueyan,et al.Characteristics and strategies of three major contradictions for continental facies multi-layered sandstone reservoir at ultra-high water cut stage[J].Acta Petrolei Sinica,2015,36(2):210-216.
[5] OUYANG Liangbiao.Practical consideration of an inflow control device application for reducing water production[R].SPE 124154,2009.
[6] AUGUSTINE J R,MCINTYRE A,ADAM R J,et al.Increasing oil recovery by preventing early water and gas breakthrough in a west brae horizontal well:a case history[C].SPE 99718,2006.
[7] EBADI F,DAVIES D R,GARDINER A R,et al.Evaluation of added value in reservoir management by application of flow control with intelligent wells[J].Petroleum Geoscience,2008,14(2):183-196.
[8] SU H J,DOGRU A H.Modeling of equalizer production system and smart-well application in full-field studies[J].SPE Reservoir Evaluation & Engineering,2009,12(2):318-328.
[9] SUN Kai,GUO Boyun,SAPUTELLI L.Multinode intelligent-well technology for active inflow control in horizontal wells[J].SPE Drilling & Completion,2011,26(3):386-395.
[10] 王庆,刘慧卿,张红玲,等.油藏耦合水平井调流控水筛管优选模型[J].石油学报,2011,32(2):346-349.
WANG Qing,LIU Huiqing,ZHANG Hongling,et al.An optimization model of completion strings with inner-located nozzle in horizontal wells coupled with reservoirs[J].Acta Petrolei Sinica,2011,32(2):346-349.
[11] 杨进先,李海涛,董社霞,等.底水气藏水平井流入控制阀完井优化方法[J].钻采工艺,2013,36(2):45-47.
YANG Jinxian,LI Haitao,DONG Shexia,et al.Horizontal well completion optimization with inflow control devices in bottom water drive gas reservoirs[J].Drilling & Production Technology,2013,36(2):45-47.
[12] 赵旭,姚志良,刘欢乐.水平井调流控水筛管完井设计方法研究[J].石油钻采工艺,2013,35(1):23-27.
ZHAO Xu,YAO Zhiliang,LIU Huanle.Technical research on well completion design with inflow control device(ICD)in horizontal wells[J].Oil Drilling & Production Technology,2013,35(1):23-27.
[13] AL-KHELAIWI F T,BIRCHENKO V M,KONOPCZYNSKI M R,et al.Advanced wells:a comprehensive approach to the selection between passive and active inflow-control completions[J].SPE Production & Operations,2010,25(3):305-326.
[14] AL-KHELAIWI F T,DAVIES D R.Inflow control devices:application and value quantification of a developing technology[R].SPE 108700,2007.
[15] 王子健,申瑞臣,王开龙,等.基于最优控制理论的智能井动态优化技术[J].石油学报,2012,33(5):887-891.
WANG Zijian,SHEN Ruichen,WANG Kailong,et al.Dynamic optimization techniques of smart wells using optimal control theory[J].Acta Petrolei Sinica,2012,33(5):887-891.
[16] VBIRCHENKO V M,MURADOV K M,DAVIES D R.Reduction of the horizontal well's heel-toe effect with inflow control devices[J].Journal of Petroleum Science and Engineering,2010,75(1/2):244-250.
[17] BIRCHENKO V M,BEJAN A I,USNICH A V,et al.Application of inflow control devices to heterogeneous reservoirs[J].Journal of Petroleum Science and Engineering,2011,78(2):534-541.
[18] LI Zhuoyi,FERNANDES P X,ZHU Ding.Understanding the roles of inflow-control devices in optimizing horizontal-well performance[J].SPE Drilling & Completion,2011,26(3):376-385.
[19] GAVIOLI P,VICARIO R.The evolution of the role of openhole packers in advanced horizontal completions:from novel technology to a critical key to success[J].SPE Drilling & Completion,2012,27(1):75-93.
[20] ATKINSON C,MONMONT F B J.A semi-analytical model for predicting the flow into a wellbore completed by inflow control devices[J].International Journal of Engineering Science,2007,45(2/8):350-363.
[21] VALVATNE P H,SERVE J,DURLOFSKY L J,et al.Efficient modeling of nonconventional wells with downhole inflow control devices[J].Journal of Petroleum Science and Engineering,2003,39(1/2):99-116.
[22] LUO Wei,LI Haitao,WANG Yongqing,et al.A new semi-analytical model for predicting the performance of horizontal wells completed by inflow control devices in bottom-water reservoirs[J].Journal of Natural Gas Science and Engineering,2015,27:1328-1339.
[23] LUO Wei,LI Haitao,WANG Yong-qing,et al.Optimization of the number of openhole packers in horizontal wells completed by inflow control devices for different types of reservoirs[J].Journal of Engineering Research,2015,3(1):149-171.
[24] NEYLON K,REISO E,HOLMES J A,et al.Modeling well inflow control with flow in both annulus and tubing[R].SPE 118909,2009.
[25] YOUNGS B,NEYLON K J,HOLMES J A.Recent advances in modeling well inflow control devices in reservoir simulation[R].IPTC 13925,2009.

非均质底水油藏水平井ICD完井优化设计

ICD completion optimization design of horizontal wells in heterogeneous bottom-water reservoirs

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	杨立红, 朱超凡, 曾皓, 苏建政, 王益维, 武俊文, 陈旭东, 郭威. 油页岩自生热原位转化直井与水平井开发效果数值模拟——以鄂尔多斯盆地旬邑地区油页岩为例[J]. 石油学报, 2023, 44(8): 1333-1343.
[2]	高永海, 尹法领, 张党生, 孙小辉, 赵欣欣, 陈野, 孙宝江. 水合物储层水平井钻井井筒-储层耦合模型与井壁稳定性分析[J]. 石油学报, 2023, 44(7): 1151-1166.
[3]	鲜保安, 高德利, 徐凤银, 毕延森, 李贵川, 王京光, 张洋, 韩金良. 中国煤层气水平井钻完井技术研究进展[J]. 石油学报, 2023, 44(11): 1974-1992.
[4]	陈志明, Yu Wei, 石璐铭, 胡连博, 廖新维. 压裂水平井的多模式裂缝网络试井模型及参数评价——以吉木萨尔页岩油为例[J]. 石油学报, 2023, 44(10): 1706-1726.
[5]	李宁, 冯周, 武宏亮, 田瀚, 刘鹏, 刘英明, 刘忠华, 王克文, 徐彬森. 中国陆相页岩油测井评价技术方法新进展[J]. 石油学报, 2023, 44(1): 28-44.
[6]	唐雪平, 洪迪峰, 高文凯, 彭烈新, 杨宝斌. 七段制恒工具面角三维水平井轨道设计方法[J]. 石油学报, 2022, 43(9): 1315-1324.
[7]	史晓东, 孙灵辉, 战剑飞, 李斌会, 韩雪, 陆慧敏, 蒋成刚. 松辽盆地北部致密油水平井二氧化碳吞吐技术及其应用[J]. 石油学报, 2022, 43(7): 998-1006.
[8]	柳军, 杜智刚, 郭晓强, 殷腾, 俞海, 曹大勇. 水平井裸眼分段压裂完井管柱下入屈曲磨损预测模型及规律[J]. 石油学报, 2022, 43(11): 1632-1641.
[9]	胡松, 王敏, 刘伟男, 王兵. 页岩水平井声波时差各向异性校正方法及其应用[J]. 石油学报, 2022, 43(1): 58-66.
[10]	罗红文, 李海涛, 李颖, 汪凤, 向雨行, 蒋贝贝, 于皓. 低渗透气藏压裂水平井产出剖面与裂缝参数反演解释[J]. 石油学报, 2021, 42(7): 936-947.
[11]	郜益华, 张迎春, 杨宝泉, 李珂, 苑志旺, 康博韬, 张昕, 张旭, 陈国宁. 复杂断块油田跨断层水平井产能预测及分段长度优化方法——以西非A深水油田为例[J]. 石油学报, 2021, 42(7): 948-961.
[12]	李国欣, 吴志宇, 李桢, 陈强, 鲜成刚, 刘合. 陆相源内非常规石油甜点优选与水平井立体开发技术实践 ——以鄂尔多斯盆地延长组7段为例[J]. 石油学报, 2021, 42(6): 736-750.
[13]	张家强, 李士祥, 李宏伟, 周新平, 刘江艳, 郭睿良, 陈俊霖, 李树同. 鄂尔多斯盆地延长组7油层组湖盆远端重力流沉积与深水油气勘探——以城页水平井区长7₃小层为例[J]. 石油学报, 2021, 42(5): 570-587.
[14]	张胜飞, 孙新革, 苟燕, 张忠义, 王红庄, 周晓义, 解阳波, 吕柏林. 流量控制器在SAGD技术中的应用现状及思考[J]. 石油学报, 2021, 42(10): 1395-1404.
[15]	刘合, 匡立春, 李国欣, 王峰, 金旭, 陶嘉平, 孟思炜. 中国陆相页岩油完井方式优选的思考与建议[J]. 石油学报, 2020, 41(4): 489-496.